From a blacksmith's shop in 1945 to industry leadership today,
Galbreath has produced waste handling equipment with a two-fold purpose: to serve
customers' requirements with the highest level of quality and to make a positive impact on
the environment. ABM Equipment is pleased to have Galbreath in our product line-up. Please
take a look below at the products that ABM Equipment and Galbreath have to offer.
MAIN PRODUCTS:
Roll-Off Hoist Features:
"Lightweight" design increases pay load up to 2000 lbs.
"Above Frame" mounting design allows for: multiple additional
axles and springs; increased ground clearance (no hoses low to the ground); no mounting
interference with drive shaft; less relocation of air tanks, fuel tanks, etc. for
mounting; unique mounting system which increases frame flexing tolerance and easy transfer
to another chassis; shorter hydraulic hoses.
"Single Cylinder" winch system means shorter cable required:
only 3 sheaves required; fewer moving parts-less maintenance; 2-1/2" sheave shafts
add a 45% increased bearing surface for longer life; all sheaves fitted with the Galbreath
Polylube Composite Bearing for low maintenance; less hydraulic hoses for fewer potential
leaks; counter-balance valves built in the winch cylinder to prevent "Run-Away".
"T-1, 110,000 PSI Fabricated Main Frame" means: longer life;
increased strength and lower weight; a 100% increase in the rated bending moment (RBM) to
2,030,000 in lb.; increased Brinell hardness for improved wear resistance.
"Automatic ICC Bumper" allows for: retracting bumper prior to
raising hoist to keep the bumper out of the dirt; dumping over curbing or bumper stops;
pin up feature for pup trailer operations as standard.
"Single Stage Lift Cylinders" mean: more power retracting and
holding the load up to 759% versus telescopic type; dual counterbalance valves built into
design for powered control in all directions, no "Run-Away".
"Full Width Hinge" for: a 270% increase in bearing area for
closer tolerance; longer lift; less maintenance; replaceable "Galbreath Polylube
Bearings" for long life.
"Standard Flex Feature" allows for: multiple container design;
various hoist configurations even after mounting; handling either outside rail, HH, inside
rail containers or all three; options to be added even after mounting.
"Galbreath Polylube Composite Bearings" mean: zero grease
fittings for low maintenance; all wear points can be returned to "brand new"
tolerances; manufacturing tolerances are minimized for "tighter fits".
"Galbreath Hydraulic System" for: the cleanest system in the
industry; polyurethane oil reservoir-no steel tank to rust and contaminate the oil; micron
filters for both air and oil for long life; all American made components.
"Three Year Warranty" on all components and structure.
Hook Hoist Features 
Offer superior maneuverability
Tolerates imperfect alignment
Up to a 62 degree dump angle for clean discharge
Power loading and unloading for ultimate control
Superior in cab operation
Application engineered
Additional Features
Bolt on replaceable hook for 30,000 - 60,000 lb. units
All above chassis installation
Counter balance valves in cylinders deter cylinder run-away
Aluminum treadplate fenders are standard on 30,000 - 60,000 lb. units
Inside air controls are standard on 30,000 - 60,000 lb. units
Hardened steel bushings on 30,000 - 60,000 lb. units
Bumper with recessed lights are standard
Hoists are designed to be operator friendly with pup trailer use
Standard components American-made
2-year warranty on all hydraulic components
Poly hydraulic tank is standard on 30,000 - 60,000 lb. units
Transfer and Dumping Trailers
Galbreath manufactures both transfer trailers and dumping trailers. All
trailers come with a full list of options such as; walking floors, full eject, frameless
dumping and full frame models.
Compactors
Types of Compactors
HORIZONTAL STATIONARY COMPACTOR
Waste type: Dry-mixed paper, corrugated, wood, plastic, etc.
Application: Retail/department store, industrial, warehouse.
Examples: 2,3,4 cu. yd. stationary, 40 cu. yd. container.
SELF-CONTAINED COMPACTOR
Waste type: Wet-garbage, food processing, medical.
Application: Supermarket (produce/meat waste), restaurant mall, hospital.
Examples: 20, 30, 35 cu. yd. self-contained.
FRONTLOAD/REARLOAD COMPACTOR
Waste type: Primarily wet, garbage, food waste.
Application: Fast food, nursing home, small grocery store.
Examples: 6 cu. yd.
Self Dumping Hoppers 
Self Dumping Hopper Features:
Standard Hopper Lock
Plate Mounted Operating Instructions
Press Fitted Rocker Pins
Optional Paint Colors
Spring Loaded Latch with Reinforced Latch Pin
Optional Equipment:
Semi-Steel, Rubber Mold, Phenolic, or Polyurethane Casters.
Hopper Floor Lock
Crane Pick-up Eyes
Three way Forklift Entry
Platform Legs
Bailers 
Vertical & Horizontal Bailers
Prompt Delivery
We deliver and unload directly at your facility, using our own equipment and
personnel.
Installation
Galbreath service technicians will install your new baler, provide operating
instruction, and ensure proper working order before leaving your facility.
Service Support
Should a problem ever develop, ABM Equipment's Service Department is available to
provide service support long after the sale including parts and qualified technicians.
Containers
R MODEL 
Standard Features:
7 gauge floor...12 gauge sides.
31/8" X 51/2" side braces on 36" centers.
6" X 2" X 1/4" rectangular tube long sills.
31/2" X 6" formed 12 gauge top cap w/10 gauge front corner caps.
3" structural channel cross members on 18" centers. Each cross member is
gusseted & welded to the long sill.
6 5/8" O.D. X 10" rear rollers (except bale style).
1 1/4" X 1/4" tarp rail.
7 gauge formed rub rail.
Solid steel nose cone added to the front of the long sills to reduce impact damage.
Serial number welded to container.
Heavy duty rear door hinges with grease fittings.
CAM type rear door closing device.
Rear door safety chain & brackets.
Rear door hinged streetside.
Rear container hold downs.
Greaseable wear points.
Outside rail understructure.
Primed & finish painted any standard Galbreath color.
T MODEL 
Standard Features:
7 gauge floor...10 gauge sides.
6" X 2" X 1/4" rectangular tube long sills.
4" wide X 6" high X 3/16" rectangular tube top cap.
3" structural channel cross members on 18" centers. Each cross member is
gusseted & welded to the long sill.
6 518" O.D. X 10" rear rollers (except bale style).
Tarp hooks.
Solid steel nose cone added to the front of the long sills to reduce impact damage.
Interior gussets.
Serial number welded to container.
Heavy duty rear door hinges with grease fittings.
CAM type rear door closing.
Rear door safety chain & brackets.
Rear door hinged streetside.
Rear container hold downs.
Greaseable wear points.
Outside rail understructure.
Primed & finish painted any standard Galbreath color.
PR MODEL 
Standard Features:
7 gauge floor...10 gauge sides.
4 3/8" X 5 3/4" side braces on 36" centers.
3-1/8 X 5-1/2" roof braces on 36" centers.
6" X 2" X 1/4" rectangular tube long sills.
3" structural channel cross members on 18" centers. Each cross member is
gusseted & welded to the long sill.
6-5/8" x 10" rear rollers (except bale style).
Containers are tapered from 78" at the front, to 84" at the rear.
Inspection door at front of container.
Heavy duty 1 piece grab pockets for compactor attachment.
10 gauge formed rub rail.
Solid steel nose cone added to the front of the long sills to reduce impact damage.
Serial number welded to container.
Heavy duty rear door hinges with grease fittings.
Flush with tarp pin off rear door.
Ratchet type rear door closing.
Rear door safety chain & brackets.
Rear door hinged streetside.
Rear container hold downs.
Greaseable wear points.
Outside rail understructure.
Primed and finish painted any standard Galbreath color.
OPR MODEL 
Standard Features
7 gauge floor & sides.
10 gauge roof & front.
6" X 2" X 1/4" rectangular tube long sills.
3" structural channel cross members on 18" centers. Each cross member is
gusseted & welded to the long sills.
6-5/8" X 10" rear rollers (except bale style).
Inspection door at front of container.
Heavy duty one piece grab pockets for compactor attachment.
Solid steel nose cone added to the front of the long sills to reduce impact damage.
Serial number welded to container.
Heavy duty rear door hinges with grease fittings.
Maximum compactor door opening (48" high X 641/2" wide).
Flush with tarp pin off rear door.
Ratchet type rear door hinges with grease fittings.
Rear door safety chain & brackets.
Rear door hinged streetside.
Rear container hold downs.
Greaseable wear points.
Outside rail understructure.
Primed & finish painted any standard Galbreath color.
Be sure to contact ABM Equipment & Supply, Inc. for all of
your service and replacement part needs. Contact Jason Herrmann @ 800-229-5451 or
952-938-5451.
[ Home ] [ Back ] [ Leach ] [ Galbreath ] [ Wayne ] [ Refuse Accessories ] [ Refuse Sales Staff ] [ Toter ]
